10w CDMA 800MHz Mobile Signal Repeater Outdoor For South America
Descriptions:
The 10W Mobile Signal Repeater is the kind of repeater used most
frequently. It has a simple structure to
transparently convey and amplify the wireless signal (at the same
frequency) between the BTS (Base
Transceiver Station) and mobiles in Dual wireless network.
The 40dBm Mobile Signal Repeater is working as a relay between the
BTS and mobiles. It picks up the
signal from the BTS via the Donor Antenna, linearly amplifies the
signal and then retransmits it via the
Coverage Antenna (or the Indoor Signal Distribution System) to the
weak/blind coverage area. And the
mobile signal is also amplified and retransmitted to the BTS via
the opposite direction.
Features:
1. Aluminum-alloy casing with IP65 protection has high resistance
to dust, water and corroding;
2. Highly selective channel selector can process multiple channels
simultaneously;
3. No interference to BTS by adopting linear amplifier with high
gain and low noise;
4. Adopting filter with highly selectivity and low insertion loss
eliminates interference between uplink and downlink;
5. (Optional)USB port provides a link to a notebook for local
supervision or to the built-in wireless modem to communicate with
the NMS (Network Management System) that can remotely supervise
repeater's working status and download operational parameters to
the repeater.
The RF Repeater is mainly applicable to such case:
1. The repeater can find an installation place which can receive
pure BTS signal at strong enough level and can meet the requirement
of isolation to avoid self-oscillation;
2. And the distance between the BTS and the area to be covered is
2km around.
In comparison with FSR (frequency shift repeater) and FOR (fiber
optic repeater), the RF Repeater has the following benefits and
disadvantages:
Pro:
Easy to build the installation site;
Lower cost of equipment and site-building.
Con:
1. Inappropriate installation may cause self-oscillation;
2. The Coverage Antenna shall face against the Donor Antenna, which
limits the coverage angle;
3. High signal noise may be introduced since the Donor Antenna
picks up signal from the air;
4. The repeater shall be installed within the coverage of BTS.
Specifications:
| GSM 850 |
| Working Frequency (customizable) | Uplink (MHz) | 824- 849MHz |
| Downlink (MHz) | 869- 894MHz |
| Working Bandwidth | 25 MHz |
| Max. Input Level (Non-Destructive) | -10dBm |
| Max. Output Power (customizable) | 40dBm |
| Max. Gain | ≥ 95dB |
| Gain Adjustment Range | 1~31 dB @ step of 1dB |
| Voltage Standing Wave Ratio (VSWR) | < 1.5 |
| Spurious Emission | Within working band | ≤ -15dBm/30kHz |
Out of working band
(Δf > 2.5MHz) | 9kHz~1GHz: ≤ -36dBm/30kHz |
| 1GHz~12.75GHz: ≤ -30dBm/30kHz |
| Noise Figure | ≤ 5dB |
| In-Band Ripple | ≤ 3dB |
| Third-Order Intermodulation | ≤ -45dBc/30kHz (measured under rated output power) |
| System Delay | ≤ 5.0μSec |
| I/O Impedance | 50Ω |
| RF Connector | N-Type (Female) / changeable / bottom of casing |
| Temperature Range | Operation: -25°C ~ +55°C / Storage: -30°C ~ +60°C |
| Relative Humidity Range | ≤ 95% (non condensing) |
| Power Supply (customizable) | AC 220V, 50/60Hz / AC 110V, 50/60Hz |
| Power Consumption | ≤ 200W |
| Backup Power Supply (optional) | 4 hours |
| Casing Level | IP65 |
| Dimensions | 550mm X 440mm X 235mm |
| Weight | 40kg |
| NMS Monitoring Function (optional) | Real-time alarm for door status, temperature, power supply, LNA,
VSWR, self-oscillation, etc. Remote control such as turn on/off,
increasing/decreasing output power, etc. Real-time status for
output/input power, UL/DL gain, all status of repeater etc. |
Application:
To expand signal coverage or fill signal blind area where signal is
weak or unavailable.
Outdoor: Airports, tourism regions, golf courses, tunnels,
factories, mining districts, villages, highways
Indoor: Hotels, exhibition centers, basements, shopping malls,
offices, parking lots.
